ONKYO TX-NR1000 User Manual download pdf (Page 3)

Precautions

1. Recording Copyright

Unless it’s for personal use only, recording copyrighted

material is illegal without permission of the copyright

holder.

2. AC Fuse

The AC fuse inside the TX-NR1000/TX-NR5000E is not

user-serviceable. If you cannot turn on the TX-NR1000/

TX-NR5000E, contact your Onkyo dealer.

3. Care

Occasionally you should dust the TX-NR1000/

TX-NR5000E all over with a soft cloth. For stubborn

stains, use a soft cloth dampened with a weak solution of

mild detergent and water. Dry the TX-NR1000/

TX-NR5000E immediately afterwards with a clean cloth.

Don’t use abrasive cloths, thinners, alcohol, or other

chemical solvents, because they may damage the ﬁnish or

remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST

TIME, READ THE FOLLOWING SECTION CAREFULLY.

AC outlet voltages vary from country to country. Make sure

that the voltage in your area meets the voltage requirements

printed on the TX-NR1000/TX-NR5000E’s rear panel (e.g.,

AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The Worldwide model has a voltage selector for compatibility

with power systems around the world. Before you plug in this

model, make sure that the voltage selector is set to the correct

voltage for your area.

For USA, Canadian, and Australian models

Setting the [STANDBY/ON] switch to STANDBY does not

fully shutdown the TX-NR1000/TX-NR5000E. If you do not

intend to use the TX-NR1000/TX-NR5000E for an extended

period, remove the power cord from the AC outlet.

For British Models

Replacement and mounting of an AC plug on the power supply

cord of this unit should be performed only by qualiﬁed service

personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with

the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire that is coloured blue must be connected to the termi-

nal that is marked with the letter N or coloured black.

The wire that is coloured brown must be connected to the ter-

minal that is marked with the letter L or coloured red.

IMPORTANT

The plug is ﬁtted with an appropriate fuse. If the fuse needs to

be replaced, the replacement fuse must be approved by ASTA

or BSI to BS1362 and have the same ampere rating as that

indicated on the plug. Check for the ASTA mark or the BSI

mark on the body of the fuse.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR

THE SOCKET OUTLET IN YOUR HOME THEN THE

FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF

AND DISPOSED OF SAFELY. THERE IS A DANGER OF

SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG

IS INSERTED INTO ANY 13 AMPERE SOCKET.

If in any doubt, consult a qualiﬁed electrician.

For U.S. Models

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Section 820-40 of the NEC which provides guide-

lines for proper grounding and, in particular, speciﬁes that the

cable ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

FCC Information for User

CAUTION:

User changes or modiﬁcations not expressly approved by the

party responsible for compliance could void the user’s author-

ity to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the

receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE:

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH

CANADIAN ICES-003.

RSS 210, Low Power Licence-Exempt Radiocommunications

Devices (All FrequencyBands).

For models having a power cord with a polarized plug:

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle Canadien

REMARQUE:

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST

CONFORME À LA NORME NMB-003 DU CANADA.

CNR-210, Dispositifs de radiocommunications de faible

puissance, exempts de licence (pour toutes les bandes de

fréquences).

Sur les modèles dont la ﬁche est polarisée:

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE

LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

1 2 3 4 5 6 7 8 ... 151 152

Comments to this Manuals

No comments

ONKYO TX-NR1000 User Manual Page 3

Comments to this Manuals

Related products and manuals for AV receivers ONKYO TX-NR1000