ONKYO TX-NR3030 Instruction Manual download pdf (Page 6)

Step 1:

Connections

Ceiling speakers, etc. are used for maximizing effects in

Dolby Atmos or Dolby Surround listening mode. Install

Top Front speakers midway between the position just

above the listening position and the position just above

the front speakers. Install Top Middle speakers just above

the listening position. Install Top Rear speakers midway

between the position just above the listening position and

the position just above the surround back speakers.

Combination patterns for Height speakers 1 and 2

Dolby recommends the following combination pattern

to obtain the best effect of Dolby Atmos and Dolby

Surround listening modes.

r Pair 1: Top Middle

r Pair 2: Top Front / Top Rear

The following are the patterns of Height speakers 2 that

can be selected according to the type of Height speakers 1.

Height speakers1: Front High

Height speakers 2: Not Use/Top Middle/Rear High/Dolby

Enabled Speaker (Surround)/Dolby Enabled Speaker (Back)

Height speakers1: Top Front

Height speakers 2: Not Use/Top Rear

Height speakers1: Top Middle

Height speakers 2 cannot be used.

Height speakers1: Dolby Enabled Speaker (Front)

Height speakers 2: Not Use/Dolby Enabled Speaker

(Surround)/Dolby Enabled Speaker (Back)

Height speakers1: Dolby Enabled Speaker (Surround)

Height speakers 2 cannot be used.

Height speakers1: Dolby Enabled Speaker (Back)

Height speakers 2 cannot be used.

r When front speakers are bi-amp connected, you can select

a pattern for Height speakers 2 from the following options.

Not use/Front High/Top Front/Top Middle/Dolby Enabled

Speaker (Front)/Dolby Enabled Speaker (Surround)/Dolby

Enabled Speaker (Back)

Instructions on how to connect speakers

Important%QPPGEVURGCMGTUYKVJŝVQŝKORGFCPEG

You have to change the setting if any of the speakers have

ŝQTOQTGVQNGUUVJCPŝKORGFCPEG;QWECPUGVWRD[

viewing the guidance displayed on the TV screen. Press

RECEIVER and then HOME on the remote controller.

Select "Setup" - "2.Speaker Setup" - "Speaker Settings" -

"Speaker Impedance" and change the default value from

"6ohms" to "4ohms".

r Select the item with the cursor buttons of the remote

controller and press ENTER to confirm your selection. To

return to the previous screen, press RETURN.

1/2"-5/8"(12-15 mm)

Cut and remove the plastic coating from the end of the

speaker cable, twist the core and connect it to the terminal.

Make correct connection between the unit's jacks and

speaker's jacks (+ to + and - to -) for each channel. If

connection is wrong, a bass sound may become poor

due to reverse phase. Attaching the supplied colored

speaker cable labels to the + side on the both ends of each

channel's cable will help correct connection.

Connecting the Subwoofer

Up to four subwoofers with built-in power amplifier can

be connected to the subwoofer jacks. Set the cut-off

filter selection switch of the subwoofer to DIRECT. If the

subwoofer does not have a cut-off filter selection switch

If you use only one surround

back speaker, connect it to

the BACK L terminal.

Height 1 R

Height 1 L

Center

Height 2 R/

Wide R

Height 2 L/

Wide L

Front R

Front L

Surround back R

Surround back L

Surround L

Surround R

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Comments to this Manuals

No comments

ONKYO TX-NR3030 Instruction Manual Page 6

Comments to this Manuals

Related products and manuals for AV receivers ONKYO TX-NR3030