ONKYO TX-NR3030 Instruction Manual download pdf (Page 4)

Step 1:

Connections

The unit supports the HDMI Through function that allows

transmission from players to the TV even if the unit is in

standby. You have to modify the settings to enable the input

selection link with CEC compliant device, connection with

ARC compatible TV, and HDMI Through function. See "2nd

Step : Source Connection" of "Step 2: Setting Up".

r To enjoy HDCP2.2 protected video, connect the player to

the IN3 jack and the TV to the HDMI OUT MAIN jack of

the unit. Your player and TV need to support HDCP2.2.

r To play 4K or 1080p video, use the high speed HDMI cable.

r It is possible to send video and audio of an MHL-enabled

mobile device by connecting the MHL-enabled mobile device

to the AUX INPUT HDMI/MHL jacks on the front panel.

Connecting Components without HDMI

If your AV component does not have HDMI jack, use an

available jack of your component for cable connection with

this unit. Just as the HDMI jacks, other jacks on this unit have

a preassigned input selector button on the front panel. See

the name of the input selector button shown with the jack

when connecting the device.

4 6



Audio signal connection

Digital connection: Use a digital optical cable

(OPTICAL) or digital coaxial cable (COAXIAL) for

connection with a player.

Digital optical cable (OPTICAL)

¼

As the digital in optical jack of the unit has a

cover, push in the cable against the cover as it is

turned inside.

Digital coaxial cable (COAXIAL)

Analog connection: Use an analog audio (RCA) cable

for connection with a player.

To enjoy multi-zone playback of audio of a CD player

or such other player without HDMI output jack, you

need to use the analog audio (RCA) cable to connect

the corresponding jacks of the player and this unit.

For details on the multi-zone function, see the section

6 "Using the multi-zone function" of "Step 3: Playing

Back".

Analog audio (RCA) cable

Connection with turntable: If it uses an MM type

cartridge and does not have a built-in audio equalizer,

connect it to the

PHONO jack. If the connected

turntable has a built-in audio equalizer, connect it to the

TV/CD jack.

¼

If it uses an MC type cartridge, install an audio equalizer compatible

with MC type cartridge between the unit and the turntable by

connecting it to the

TV/CD jack. For details, refer to the turntable's

instruction manual.

¼

If the turntable has a ground wire, connect it to the GND terminal of

this unit. If connecting the ground wire increases noise, disconnect it.



Video signal connection

The unit has a video upconversion function. For details, see

the section on the right.

Use a component video cable to connect a TV

with component video input jacks and a player with

component video output jacks.

Component video cable

¼

Its transmitted video has higher quality than that

of composite video cable.

Use a composite video cable to connect a TV with

composite video input jack or a player with composite

video output jack.

Composite video cable

Use an analog RGB cable to connect the unit with a PC.

Analog RGB cable

¼

Video signals from the PC connected with the PC IN port will be

output only to a TV connected with the HDMI OUT MAIN/SUB/

<10'|LCEM

Video signals input to the composite video input jack,

the COMPONENT VIDEO input jack, or the PC IN

port will be upconverted to HDMI signals and then

output from the HDMI output jack. Note that it is

not possible to convert digital audio input signals to

analog or vice versa.

AV Receiver

¼

If multiple video signal inputs are put into one input

system, the output will be made in the order of HDMI,

component video, and composite video.

1 2 3 4 5 6 7 8 9 ... 23 24

Comments to this Manuals

No comments

ONKYO TX-NR3030 Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for AV receivers ONKYO TX-NR3030