ONKYO TX-NR3030 Instruction Manual download pdf (Page 9)

Step 2:

Setting Up

After placing the microphone at the measurement

position, select "Do it Now" with the cursors and

press ENTER.

Connect the microphone to the SETUP MIC jack of

the unit.

SETUP MIC jack

Speaker

setup

microphone

Follow the guidance displayed on the TV screen.

AccuEQ Room Calibration

Front Speakers Type

Height 1 Speakers Type

Height 2 Speakers Type

Normal

Not Use

Set bi-amp only if you use 2 channel amp for each front speaker.

ENTER Nex t

REAR PANEL

SURROUND

WIDE

BACK

FRONT R FRONT L

When the screen above is displayed, set the items with the

cursors on the remote controller. Select the types for height

1/2 speakers if the height speakers are used. After front and

height speakers types are selected, switch the screen using

cursor

to select the type of subwoofer. After setting the

items, press ENTER on the remote controller. Press ENTER

again in the next screen to start automatic speaker setting.

r Speaker terminals and settings description display

at the bottom of the screen as you move the cursor

to each item. Please refer to this information on the

screen.

The test tones sound from the connected speakers

and automatic speaker setting starts.

Measurement will be made twice for each speaker. It takes

several minutes to be completed. Keep the room as quiet

as possible during measurement. If any of the speakers

do not produce the test tone, check for disconnection.

r During measurement, each speaker outputs the test

tones at a high volume. Be careful of sound leak

that may disturb your neighbors, or be careful not to

frighten young children.

When the measurement is completed, the

measurement result is displayed.

Press

on the remote controller to check the

settings. Press ENTER with "Save" selected. In the next

screen showing that "AccuEQ Room Calibration" is

"On", press ENTER on the remote controller.

r If there is an error message, follow the on-screen

instruction to remove the error cause.

About THX playback

THX recommends setting the speakers manually if

you use THX-certified speakers or playing back with

THX listening modes.

r

THX recommends setting the crossover frequency to

“80Hz(THX)” manually.

r Due to the electrical complexities and the

interaction with the room, you may notice irregular

results when setting the level or distance of each

speaker. If this happens, THX recommends setting

the speakers and the subwoofer manually.

When "Please unplug setup microphone." is

displayed, disconnect the microphone.



2nd Step : Source Connection

You can check whether or not each input source is

connected correctly.

When the Source Connection start screen is displayed,

select "Yes, Continue" with the cursors and press ENTER.

This step will start to check if the

connections were made correctly.

Would you like to continue?

Yes, Continue

No. Skip

Initial Setup

Source Connection

ExitHOME

Select the desired input to check the connection and

press ENTER.

Start playback of the selected device. If connection is

correct, video/audio of the input source selected on the

unit will be played.

After checking the connection, select "Yes" with the

cursors and press ENTER.

r If you select "No" and press ENTER, the error cause

will be displayed. Follow the guidance to remove the

error cause and check the connection again.

Select "Yes" with the cursors and press ENTER

on the remote controller to check the connection

of other inputs or select "No, Done Checking" and

press ENTER to skip.

If you select "Yes", you will return to the screen of step 2.

If you select "No, Done Checking", you will proceed to step 5.

Enabling HDMI Linked Operation and Other Functions

In the next screen, you can enable the HDMI linked

operation with CEC compliant device, connection with ARC

compatible TV, and HDMI Through function. Select "Yes"

with the cursors to enable them or "No, Done Checking" to

skip, and press ENTER on the remote controller.

Select "Yes" with the cursors and press ENTER to

enable the CEC link function or select "No" and

press ENTER to keep it disabled.

The following CEC-compatible devices are found;

Do you wish to turn on the CEC link?

Integra DHS-8.8

Yes

Source Connection

ExitHOME

If you select "Yes", the connection with ARC compatible TV

and HDMI Through function will be set to "Auto" and enabled.



3rd Step : Remote Mode Setup

HOME Ex it

Initial Setup

Remote Mode Setup

Preprograming remote will give you control

of other devices from AV receiver remote

Would you like to setup your remote to

control your devices? This may take a while

depending on what and how many you have

connected. You can always come back to remote

setup from setup “8-2 Remote Mode Setup”.

Yes

No. Skip

In this step, you can enable operation of the other components

using the remote controller of the unit. When the Remote

Mode Setup start screen is displayed, select "Yes" with the

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 23 24

Comments to this Manuals

No comments

ONKYO TX-NR3030 Instruction Manual Page 9

Comments to this Manuals

Related products and manuals for AV receivers ONKYO TX-NR3030