ONKYO TX-SR444 Specifications download pdf (Page 11)

Step 2: Setting Up

En-11

3� Select the settings for the connected speakers, the

type of the height speakers, and other appropriate

settings�

AccuEQ Room Calibration

Select how many speakers you have.

Ne xt

ENTER

Speaker Channels

Subwoofer

Height Speaker

7.1ch

Yes

---

When the screen above is displayed, set the items with

the cursor buttons on the remote controller.

Refer to the on-screen diagram for "Speaker Channels",

which changes each time a different number of channels

is selected. When all the items have been set, press

ENTER on the remote controller. After that, follow the

guidance displayed on the TV screen to operate the unit.

● Refer to the content of an item, which appears on

the lower left of the screen when the cursor is on the

item.

4� The test tones sound from the connected speakers

and automatic speaker setting starts�

Measurement will be made three times or more for each

speaker. It takes several minutes to be completed. Keep

the room as quiet as possible during measurement. If

any of the speakers do not produce the test tone, check

for disconnection.

● During measurement, each speaker outputs the test

tones at a high volume. Be careful of sound leak

that may disturb your neighbors, or be careful not to

frighten young children.

● To cancel measurement on the way, disconnect the

microphone plug.

5� When the measurement is completed, the

measurement result is displayed�

Press

on the remote controller to check the

settings. Press ENTER with "Save" selected. Select

"On" in the next screen and press ENTER on the remote

controller.

● You should normally select "On (All Channels)", and

to disable just the front speakers, you should select

"On (Except Front Left/Right)".

● If there is an error message, follow the on-screen

instruction to remove the error cause.

6� When "Please unplug setup microphone�" is

displayed, disconnect the microphone�

3 HDMI Setup

The unit supports the linked system function such as power

on/off link when connected via HDMI cable with a CEC

(Consumer Electronics Control) compliant TV or player. You

need to change the default setting to use the linked system

function, HDMI Standby Through function and ARC (Audio

Return Channel) function.

HDMI CEC (RIHD)

The following linked operations are possible with connected

equipment when the CEC function is enabled.

●

Turning the TV to standby mode will turn the unit to

standby mode.

●

On the TV side, it is possible to set whether to output

audio from the speakers connected to the unit or from the

TV's speakers.

●

Starting playback of a CEC compliant player/recorder will

automatically switch the unit's input to the HDMI input of

the player/recorder. If the unit is in standby mode, it will

automatically be turned on.

It is also possible to control the connected CEC compliant

equipment with the remote controller of the unit. For details,

see the Advanced Manual.

¼ RIHD is a name for the linked system function of Onkyo's CEC compliant

products.

1� After pressing RECEIVER, press SETUP on the

remote controller�

2� Select "5� Hardware" with the cursor and press

ENTER�

3� Select "HDMI" with the cursor and press ENTER�

4� Select "HDMI CEC (RIHD)" with the cursor and

select "On"�

● When setting is complete, press SETUP to close the

menu screen.

HDMI Standby Through

The function allows transmission from players to the TV

even if the unit is in standby. Setting the HDMI CEC (RIHD)

setting mentioned above to "On" enables this setting

automatically.

● Power consumption in standby mode increases when

the HDMI Standby Through function is enabled.

ARC (Audio Return Channel)

Simple connection to the ARC compatible TV using a single

HDMI cable allows to listen to the TV audio signals from

the speakers connected to the unit. Setting the HDMI CEC

(RIHD) setting mentioned above to "On" enables the "Audio

Return Channel" setting automatically.

Audio output of connected players

To enjoy digital surround sound including Dolby

Digital and DTS, audio output should be set to

"Bitstream output" on the connected Blu-ray Disc

Player or other device.

Depending on the settings on the Blu-ray Disc Player,

there may be cases when Dolby TrueHD, Dolby

Atmos, and DTS-HD Master Audio is not output

according to the format of the source.

In this case, in the Blu-ray Disc Player settings

try setting "BD video supplementary sound" (or

secondary sound) to "Off".

Change the listening mode after changing the setting

to confirm.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 87 88

Comments to this Manuals

No comments

ONKYO TX-SR444 Specifications Page 11

Comments to this Manuals

Related products and manuals for AV receivers ONKYO TX-SR444