ONKYO PR-SC5508 User Manual download pdf (Page 104)

104

Firmware Update

There are the following methods to update the firmware:

via network and via USB storage. Please choose either one

that suits your condition. Before you start, carefully read

the update procedure. It will take about 60 minutes to

update the firmware.

■ Update via network

You need a wired Internet connection to update the

firmware.

■ Update via USB storage (➔ 105)

Please prepare a USB storage device such as a USB

flash memory stick. You need at least 32 MB of avail-

able space to update the firmware.

Note

• The storage media in the USB card reader may not work.

• If the storage device has been partitioned, each section will be

treated as an independent device.

• If the USB mass storage device contains a lot of data, the AV

controller may take a while to read it.

• Operation with all USB mass storage devices including the abil-

ity to power them is not guaranteed.

• Onkyo accepts no responsibility whatsoever for the loss or dam-

age to data stored on a USB mass storage device when that

device is used with the AV controller. We recommend that you

back up your important music files beforehand.

• If you connect a USB hard disk drive to the USB port, we rec-

ommend that you use its AC adapter to power it.

• USB hubs and USB devices with hub functions are not sup-

ported. Do not connect your USB mass storage device via a USB

hub.

• USB memory devices with security functions are not supported.

• In no event shall Onkyo be liable to you or any third party for any

damages, whatsoever, arising from your use of or inability to use

the firmware, including but not limited to, loss of any equipment,

media or data, or other special, incidental or consequential dam-

ages, even if Onkyo has been advised of the possibility of such

damages.

The AV controller allows you to update firmware using net-

work connection on rear panel.

In this procedure, on-screen display may vary depending on the

model.

Note

• Make sure your AV controller and TV are turned on and Ethernet

cable is connected to rear panel of the AV controller.

• Never unplug or turn off the AV controller during updating pro-

cess.

• Never plug or unplug an HDMI cable and Ethernet cable during

updating process.

• Never unplug the power cord during updating process.

• Do not access the AV controller from PC during updating pro-

cess.

• It will take about 60 minutes to update the firmware.

• The AV controller will retain all your settings after update is fin-

ished.

Before you start

• Check “HDMI Control(RIHD)” setting (➔ 61). The

update may not be successful if this setting is on.

• Turn off the controller device connected via RS232C and

via Ethernet network.

• Turn off Zone 2 and Zone 3.

• Stop playback of content from Internet radio, iPod, USB

or servers, etc.

■ How to turn off RIHD

Update procedure

See the Onkyo web site for latest information.

Updating the Firmware via Network

In the Main menu select “Hardware Setup”.

Select “HDMI”.

Set “HDMI Control(RIHD)” to “Off”.

Press RECEIVER followed by SETUP on the

remote controller.

Main menu will be displayed on TV screen. Proce-

dures thereafter can also be performed on the AV

controller by using its SETUP, arrow, and ENTER

buttons.

Go to “Hardware Setup” menu.

Go to “Firmware Update” menu.

Note that the Firmware Update option will be grayed

out about 50 seconds after the AV controller is

turned on. Please wait.

Select “via NET” and press ENTER.

Select “Update” and press ENTER.

Updating will begin.

As the updating progresses, the TV screen may dis-

appear depending on the program updated. In this

case, you can see the update progress on the front

display of the AV controller. The TV screen will

reappear when you finish the update and turn on the

AV controller.

Message “Complete!” appears on the front dis-

play of the AV controller, indicating that the

update has been completed.

Using ON/STANDBY on the front panel, turn off

and on the AV controller.

Do not use ON or STANDBY on the remote control-

ler.

Congratulations!! Now you have the latest firmware

on your Onkyo AV controller.

1 2 ... 99 100 101 102 103 104 105 106 107 108

Comments to this Manuals

No comments

ONKYO PR-SC5508 User Manual Page 104

Comments to this Manuals

Related products and manuals for AV receivers ONKYO PR-SC5508