Onkyo TX SR607 User Manual download pdf (Page 101)

101

Troubleshooting—Continued

The surround back speakers produce no sound

• Depending on the current listening mode, no sound

may be produced by the surround back speakers.

Select another listening mode (page 67).

• Not much sound may be produced by the surround

back speakers with some sources.

• Make sure the speakers are configured correctly

(page 70).

• While Powered Zone 2 is being used, playback in the

main room is reduced to 5.1-channels and the sur-

round back speakers produce no sound (page 85).

The subwoofer produces no sound

• When you play source material that contains no infor-

mation in the LFE channel, the subwoofer produces

no sound.

• Make sure the speakers are configured correctly

(page 70).

There’s no sound with a certain signal format

• Check the digital audio output setting on the con-

nected device. On some game consoles, such as those

that support DVD, the default setting is off.

• With some DVD-Video discs, you need to select an

audio output format from a menu.

• Depending on the input signal, some listening modes

cannot be selected (pages 63-66).

Can’t select the Pure Audio listening mode

• The Pure Audio listening mode cannot be selected

while Zone 2 is on. (Pure Audio listening mode is not

available for North American/Taiwan models.)

Can’t get 6.1/7.1 playback

• If no surround back speakers are connected, or the

Zone 2 speakers are being used, 6.1/7.1 playback is

not possible.

• You can not always select all of the listening modes,

depending on the number of the speakers connected

(pages 63-66).

The volume cannot be set to 79

• Check to see if a maximum volume has been set

(page 80).

• If the volume level of each individual speaker has been

adjusted to high positive values (page 72), then the

maximum master volume possible may be reduced.

Note that the individual speaker volume levels are set

automatically after the Audyssey 2EQ™ Room Cor-

rection and Speaker Setup function has been com-

pleted (

page 47

Noise can be heard

• Using cable ties to bundle audio cables with power

cords, speaker cables, and so on may degrade the

audio performance, so don’t do it.

• An audio cable may be picking up interference. Try

repositioning your cables.

The Late Night function doesn’t work

• Make sure the source material is Dolby Digital, Dolby

Digital Plus, and Dolby TrueHD (page 75).

About DTS signals

• When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listen-

ing mode and the DTS indicator remains on. This is to

prevent noise when you use the pause, fast forward, or

fast reverse function on your player. If you switch your

player from DTS to PCM, because the AV receiver

does not switch formats immediately, you may not

hear any sound, in which case you should stop your

player for about three seconds, and then resume play-

back.

• With some CD and LD players, you won’t be able to

playback DTS material properly even though your

player is connected to a digital input on the AV

receiver. This is usually because the DTS bitstream

has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver

doesn’t recognize it as a genuine DTS signal. In such

cases, you may hear noise.

• When playing DTS program material, using the pause,

fast forward, or fast reverse function on your player

may produce a short audible noise. This is not a mal-

function.

The beginning of audio received by an HDMI IN

can’t be heard

• Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio sig-

nals, audio output may not start immediately.

There’s no picture

• Make sure that all video connecting plugs are pushed

in all the way (page 22).

• Make sure that each video component is properly con-

nected. (pages 24-36)

• If your TV is connected to the HDMI OUT, select

“- - - - -” in the “HDMI Input Setup” on page 40 to

watch composite video, and component video sources.

• If the video source is connected to a component video

input, you must assign that input to an input selector

(page 41), and your TV must be connected to either

the HDMI OUT or COMPONENT VIDEO MONI-

TOR OUT (pages 27 and 24).

• If the video source is connected to a composite video

input, your TV must be connected to the HDMI OUT

or the corresponding composite video output

(pages 27 and 24).

• If the video source is connected to an HDMI input,

you must assign that input to an input selector

(page 40), and your TV must be connected to the

HDMI OUT (page 24).

• While the Pure Audio listening mode is selected, the

video circuitry is turned off and only video signals

input through HDMI IN can be output.

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

Video

1 2 ... 96 97 98 99 100 101 102 103 104 105 106 107 108

Comments to this Manuals

No comments

Onkyo TX SR607 User Manual Page 101

Comments to this Manuals

Related products and manuals for Acoustics Onkyo TX SR607