Onkyo A-9555 User Manual download pdf (Page 18)

Troubleshooting

If you have any trouble using the A-9755/A-9555, look for a solution here. If you can’t resolve the issue yourself,

contact your Onkyo dealer.

Can’t turn on the A-9755/A-9555.

• Make sure that the power cord is properly plugged into the wall outlet. (page 5)

• Unplug the power cord from the wall outlet, wait ten seconds or more, then plug it in again.

• By default, pressing the remote controller’s [ON] button once does not turn on all of the system components. You

need to press the remote controller’s [ON] button again. Alternatively, you can set the A-9755/A-9555 so that all

components do turn on simultaneously (page 14).

The STANDBY indicator is ﬂashing.

• The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately and contact

your Onkyo dealer.

There’s no sound or it’s very quiet.

• When the A-9755 is used as a power ampliﬁer (MAIN IN indicator lights up), the sound from components connected

to the preamp is output. To output the sound from a component that’s connected to the A-9755, or to use the A-9755

as a preamp, press the [POWER AMP DIRECT (MAIN IN)] button for 3 seconds until the MAIN IN indicator goes

off. (page 17)

• Make sure that all audio plugs are pushed in all the way (page 11).

• Make sure that the inputs and outputs of all components are connected properly.

• Make sure that the polarity of the speaker cables is correct and that the bare wires are in contact with the metal part

of each speaker terminal (page 10).

• Make sure that the correct input source is selected (page 15).

• If the Volume indicator ﬂashes slowly, press the remote controller’s [MUTING] button to unmute the A-9755/A-9555

(page 15).

• Make sure that none of the cables are bent, twisted, or damaged.

• To use a turntable with a moving-coil (MC) type cartridge, you need a commercially available MC phono preamp

(page 11).

• If the Volume indicator ﬂashes quickly, any speakers may not be connected to the A-9755/A-9555. Make sure that

the required connection is performed appropriately, and set the [POWER] switch to the ON position again (pages 10,

14).

• Verify if the SPEAKERS selector is conﬁgured correctly. If “OFF” is selected, no sound will be output from any of

the speakers (page 14).

Noise can be heard.

• Using cable ties to bundle audio cables with power cords, speaker cables, and so on may degrade the audio perfor-

mance, so don’t bundle them together.

• An audio cable may be picking up interference. Try repositioning your cables.

The tone controls have no effect.

• If the PURE DIRECT indicator lights up, the PURE DIRECT function is on and the tone controls have no effect.

Press the [PURE DIRECT] button to turn the function off. The PURE DIRECT indicator will go off (page 16).

The remote controller doesn’t work.

• Make sure that the batteries are installed with the correct polarity (page 5).

• Install new batteries. Don’t mix different types of batteries or old and new batteries (page 5).

• Make sure that the remote controller is not too far away from the A-9755/A-9555 and that there’s no obstruction

between the remote controller and the A-9755/A-9555’s remote control sensor (page 9).

• Make sure that the A-9755/A-9555 is not subjected to direct sunshine or inverter-type ﬂorescent lights. Relocate if

necessary (page 9).

• If the A-9755/A-9555 is installed in a rack or cabinet with colored glass doors, the remote controller may not work

reliably when the doors are closed (page 9).

Can’t control other components?

• If it’s an Onkyo component, make sure that the cable and analog audio cable are connected properly. Connecting

only an cable won’t work. (page 13)

Power

Audio

Remote Controller

1 2 ... 13 14 15 16 17 18 19 20

Comments to this Manuals

No comments

Onkyo A-9555 User Manual Page 18

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Onkyo A-9555