Onkyo TX-SA705 User Manual Page 111
- Page / 116
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
111
Troubleshooting—Continued
The surround speakers produce no sound
• When the Stereo or Mono listening mode is selected,
the surround speakers produce no sound (page 71).
• Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
• Make sure the speakers are configured correctly
(page 77).
The center speaker produces no sound
• When the Mono or Stereo listening mode is selected,
the center speaker produces no sound (page 71).
• Make sure the speakers are configured correctly
(page 77).
The surround back speakers produce no sound
• The surround back speakers are not used with all listen-
ing modes. Select another listening mode (page 71).
• Not much sound may be produced by the surround
back speakers with some sources.
• Make sure the speakers are configured correctly
(page 77).
The subwoofer produces no sound
• When you play source material that contains no infor-
mation in the LFE channel, the subwoofer produces
no sound.
• Make sure the speakers are configured correctly
(page 77).
There’s no sound with a certain signal format
• Check the digital audio output setting on the con-
nected device. On some game consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• Depending on the input signal, some listening modes
cannot be selected (pages 67-70).
Can’t select the DTS-ES Discrete/Matrix listen-
ing modes
• These modes cannot be selected when no surround
back speakers are connected, or the Zone 2 speakers
are being used.
• You can not always select all of the listening modes,
depending on the number of the speaker connected
(pages 67-70).
Can’t get 6.1/7.1 playback
• If no surround back speakers are connected, or the
Zone 2 speakers are being used, 6.1/7.1 playback is
not possible.
• You can not always select all of the listening modes,
depending on the number of the speakers connected
(pages 67-70).
The volume cannot be set to +18 dB (99)
• Check to see if a maximum volume has been set
(page 92).
• After the Automatic Speaker Setup function has been
run, or the volume level of each individual speaker has
been adjusted (page 81), the maximum volume may
be reduced.
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so don’t do it.
• An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesn’t work
• Make sure the source material is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD (page 75).
The DVD analog multichannel input doesn’t
work
• Check the DVD analog multichannel input connec-
tions (page 31).
• To select the DVD analog multichannel input, press
the [MULTI CH] input selector button.
• Check the audio output settings on your DVD player.
About DTS signals
• When DTS program material ends and the DTS bit-
stream stops, the AV receiver/AV amplifier remains in
DTS listening mode and the DTS indicator remains
on. This is to prevent noise when you use the pause,
fast forward, or fast reverse function on your player. If
you switch your player from DTS to PCM, because
the AV receiver/AV amplifier does not switch formats
immediately, you may not hear any sound, in which
case you should stop your player for about three sec-
onds, and then resume playback.
• With some CD and LD players, you won’t be able to
playback DTS material properly even though your
player is connected to a digital input on the AV
receiver/AV amplifier. This is usually because the DTS
bitstream has been processed (e.g., output level, sam-
pling rate, or frequency response changed) and the AV
receiver/AV amplifier doesn’t recognize it as a genuine
DTS signal. In such cases, you may hear noise.
• When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a mal-
function.
The beginning of audio received by an HDMI IN
can’t be heard
• Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio sig-
nals, audio output may not start immediately.
- TX-SR705 1
- TX-SA705 1
- WARNING: 2
- CAUTION: 2
- Precautions 3
- Precautions—Continued 4
- For British models 4
- For European Models 4
- Supplied Accessories 5
- Features 6
- Table of Contents 7
- Front & Rear Panels 8
- Rear Panel 11
- )5 DVD IN 13
- )7 12V TRIGGER OUT 13
- )8 IR IN 13
- Remote Controller 14
- Remote Controller—Continued 15
- About Home Theater 20
- About AV Connections 21
- Connecting Your Speakers 22
- 5/8" (15 mm) 23
- Bi-amping the Front Speakers 24
- To AV receiver To TV (or VCR) 26
- TV/FM antenna splitter 26
- Outdoor antenna 26
- Insulated antenna cable 26
- AM loop antenna 26
- MONITOR OUT 27
- Connecting a TV or Projector 29
- Connecting a DVD Player 30
- DVD player 31
- R S VIDEO 32
- Connecting a Game Console 35
- Step 1: Video Connection 36
- Step 2: Audio Connection 36
- About HDMI 37
- Supported Audio Formats 37
- About Copyright Protection 37
- 1 2 3 4 5 6 7 8 41
- Connecting an RI Dock 42
- European models only) 42
- Connecting Onkyo Components 43
- Connecting the RS232 Port 43
- Connecting the Power Cord 43
- Turning On and Standby 44
- First Time Setup 45
- Speaker Settings 46
- First Time Setup—Continued 47
- Changing the Input Display 50
- TV Format Setup 52
- (not North American models) 52
- AM Frequency Step Setup 53
- (on some models) 53
- : listening area 54
- : listening position 54
- AUDYSSEY 58
- Selecting the Input Source 59
- Basic Operations—Continued 60
- Using the Tuner 62
- Band Frequency 62
- Presetting AM/FM Stations 63
- RDS Program Types (PTY) 64
- Displaying Radio Text (RT) 65
- Selecting Listening Modes 66
- Analog and PCM Sources 67
- TrueHD and DTS Sources 69
- DTS-HD Sources 70
- About the Listening Modes 71
- Onkyo Original DSP Modes 73
- Camcorder 74
- VCRCD player 74
- Dolby TrueHD only) 75
- Using the Re-EQ Function 75
- Advanced Setup 76
- Speaker Setup 77
- Advanced Setup—Continued 78
- Audio Adjust Functions 85
- Front right speaker 86
- Front left speaker 86
- Source Setup 88
- “ ” “ ” 90
- 123456789 90
- 4-3. Name Edit 91
- Name 91
- Immediate Display 93
- Monitor Type 93
- Display Position 93
- Changing the AV Receiver/AV 94
- Amplifier’s ID 94
- Remote ID 94
- HDMI Setup 95
- 8. Lock Setup 97
- Lock Unlocked 97
- RECEIVER 98
- Connecting Zone 2 99
- Setting the Powered Zone 2 100
- Using Zone 2 101
- ZONE 2 LEVEL 102
- Zone 2—Continued 103
- Entering Remote Control Codes 104
- Components Connected via 105
- Resetting REMOTE MODE Buttons 105
- Press [TV] first 106
- Press [VCR] first 106
- Press [CABLE](SAT) 106
- Learning Commands 107
- Using Macros 108
- Specifications 109
- Troubleshooting 110
- Troubleshooting—Continued 111
- HOMEPAGE 116
Related products and manuals for Receivers and Amplifiers Onkyo TX-SA705
(52 pages)
(140 pages)© 2020, manymanuals.com. All rights reserved. | 2.789 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals