ONKYO TX-NR509 Instruction Manual download pdf (Page 46)

Audio Selector

■ Audio Selector

` ARC:

The audio signal from your TV tuner can be sent

digitally to the HDMI OUT of the AV receiver.

With this selection, the TV’s audio can be

automatically selected as a priority among other

assignments.

` HDMI:

This can be selected when HDMI IN has been

assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or

OPTICAL IN) have been assigned, HDMI input is

automatically selected as a priority.

` COAXIAL:

This can be selected when COAXIAL IN has been

assigned as an input source. If both coaxial and

HDMI inputs have been assigned, coaxial input is

automatically selected as a priority.

` OPTICAL:

This can be selected when OPTICAL IN has been

assigned as an input source. If both optical and

HDMI inputs have been assigned, optical input is

automatically selected as a priority.

` Analog:

The AV receiver always outputs analog signals.

You can set priorities of audio output when there are both

digital and analog inputs.

Note

• The setting is stored individually for each input selector.

• This setting can be made only for the input source that is

assigned as HDMI IN, COAXIAL IN, or OPTICAL IN. If both

HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or

OPTICAL IN) are assigned, HDMI input will be selected as a

priority by setting to “ARC” (➔ page 48). To select the digital

audio input, see “Digital Audio (Digital Audio Input)”

(➔ page 40).

You can select “ARC” if you select the TV/CD input selector.

But you cannot select it if you’ve selected “Off” in the

“Audio Return Ch” setting (➔ page 48).

Setting the Incoming Digital Signal (Fixed

Mode)

■ Fixed Mode

` Off

The format is detected automatically. If no digital

input signal is present, the corresponding analog

input is used instead.

` PCM:

Only 2-channel PCM format input signals will be

heard. If the input signal is not PCM, the PCM

indicator will flash and noise may occur.

` DTS:

Only DTS (but not DTS-HD) format input signals

will be heard. If the input signal is not DTS, the DTS

indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is

selected in the “Audio Selector” setting, you can then

specify the signal type in “Fixed Mode”.

Normally, the AV receiver detects the signal format

automatically. However, if you experience either of the

following issues when playing PCM or DTS material, you

can manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut

off, try setting the format to PCM.

• If noise is produced when fast forwarding or reversing a

DTS CD, try setting the format to DTS.

Note

• The setting will be reset to “Off” when you change the setting in

“Audio Selector” (➔ page 46).

Menu Hardware

OSD

■ Volume OSD

` On

` Off

You can select if you wish to display the volume level on-

screen, when it is adjusted.

Remote Control

■ Remote ID

` 1

, 2, or 3

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differentiate

the AV receiver from other components, you can change

its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

Changing the remote controller’s ID

Hardware

While holding down RECEIVER, press and hold

down SETUP until the remote indicator lights

(about 3 seconds) (➔ page 39).

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 75 76

Comments to this Manuals

No comments

ONKYO TX-NR509 Instruction Manual Page 46

Comments to this Manuals

Related products and manuals for AV receivers ONKYO TX-NR509