Integrated AmplifierA-9050/A-9030Instruction ManualThank you for purchasing an Onkyo Integrated Amplifier. Please read this manual thoroughly before m
10EnFor detailed information, see the pages in parentheses.a 8 button (➔ page 21)Sets the integrated amplifier to On or Standby.b DIMMER buttonAdjusts
11En*: A-9050 onlyConnecting Terminal LINE1/D1* LINE2/D2* LINE3/D3*ComponentButton on Remote ControllerCD Player TUNERu DOCK18882 DIMMER DIMMER DIMMER
12EnConnectionsConnections Screw-type speaker terminalsStrip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables,
13EnNote• Make sure that the wires do not touch metal parts on the back panel or elsewhere.• Y plugs cannot be connected.• Two sets of speakers (Speak
14EnNote• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions). • To prevent interference, keep audi
15EnThis is an example of connection using the CD Player.Digital Connection (A-9050 only)Tip• The CD player can be connected to the COAXIAL D1 or D2 j
16EnThis is an example of connection using the Tuner.Digital Connection (A-9050 only)Tip• The Tuner can be connected to the COAXIAL D1 or D2 jack or t
17EnThis is an example of connection using the Onkyo u Dock.Digital Connection (A-9050 only)Tip• An Onkyo Dock can be connected to the COAXIAL D1 or D
18EnWith u (Remote Interactive), you can use the following special functions: Auto Power OnWhen you start playback on a component connected via u whi
19EnThe PHONO input jacks are for use with moving-magnet (MM) type cartridges.Use an analog audio cable to connect the PHONO L/R jacks to the audio ou
2EnIntroductionImportant Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. D
20EnA subwoofer with a built-in power amplifier can be connected to be used.Connect LINE INPUT on the subwoofer with a built-in power amplifier to PRE
21EnTurning On & Basic OperationsBasic OperationsTurning On the Integrated Amplifier Operating with the remote controller Operating on the integ
22EnYou can select to output sound from Speakers A, Speakers B, or both A + B.Note• While headphones are connected, this setting is disabled.• When th
23EnYou can switch inputs to select the desired source component. Choose an input from the following:LINE1, LINE2, LINE3, LINE4, LINE5, PHONO (D1, D2,
24EnYou can adjust the bass, treble and left/right output balance respectively. Operating on the integrated amplifierTip• By default, bass, treble an
25EnAdvanced OperationsCustom SetupWhen the Auto Standby (ASb) function is activated, the integrated amplifier will automatically enter Standby mode i
26EnOthersTroubleshootingFirst check the followings.Since the issue may be caused by other components that are connected, be sure to also check them w
27EnThere’s no sound.• Make sure that the Onkyo Dock is connected to the integrated amplifier properly.• Make sure that no video content is being play
28EnSpecifications Audio Inputs Audio Outputs OthersSpecifications and features are subject to change without notice.A-9050 A-9030Rated Output Powe
29EnMEMO
3EnPrecautions1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyri
30EnMEMO
31EnMEMO
SN 29401270(C) Copyright 2012 Onkyo Corporation Japan. All rights reserved.C1207-12-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPANTel: 072-831-80
4EnFor British modelsReplacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service person
5EnFeaturesA-9050 Integrated Digital Amplifier• Three-stage Inverted Darlington Circuitry• Digital Inputs (Optical/Coaxial)• Wolfson 192 kHz/24 bit DA
6EnContentsIntroductionImportant Safety Instructions ...2Precautions ...
7EnBefore Using the Integrated AmplifierNote• If the remote controller doesn’t work reliably, try replacing the batteries.• Don’t mix new and old batt
8EnGetting to Know the Integrated AmplifierFor detailed information, see the pages in parentheses.a 8ON/STANDBY button (➔ page 21)Sets the integrated
9Ena GND screwConnects the turntable’s ground wire.b u MODE selector (A-9050 only)c DIGITAL IN OPTICAL D3 jack (A-9050 only)Connects components such a
Comments to this Manuals