Onkyo TX-DS676 User Manual download pdf (Page 21)

Using the test tone to adjust the speaker output

levels

1. Press the SP/SYS SETUP button repeatedly until

“Level Setup?” appears.

Press the SMART SCAN CONTROLLER.

The display shows “Left.”

2. Rotate clockwise or counterclockwise the SMART SCAN

CONTROLLER to adjust the speaker output level.

You can adjust the output level of each speaker in the range of

12 to +12 dB, except for the subwoofer whose adjustment range

is -30 to +10 dB.

Press the SMART SCAN CONTROLLER.

You hear a test tone (pink noise) from the left front speaker.

Each time you press the SMART SCAN CONTROLLER, the

speaker that produces a test tone changes as below. Set the out-

put level of each speaker by rotating the SMART SCAN CON-

TROLLER so that you can hear the same level of test tone at the

listening position.

Left (Left front)

Center (Center) Right (Right front) R-Sur

(Right surround)

L-Sur(Left surround) Subwoofer (Subwoofer)

Left

Notes:

• In order to correctly set the output levels, use a hand-held Sound

Pressure Level meter (SPL), set to C-Weighting and Slow aver-

aging. A Radio Shack

SPL meter (catalogue number 330-

2055) or equivalent can be used. Using the internal channel

noise generators, set each channel so that you read 75 dB SPL

from each channel.

• SPEAKER B, when selected, will be deselected automatically

as soon as the test tone starts sounding. The Test Tone function

is not available when the headphones are connected or when

MULTI CH INPUT is selected.

• The test tone will not be output from the speaker that has been set to

"No" in the configuration setup explained on the page 18,19.

• If the speaker level is set to +1dB or higher , the maximum level indi-

cated on the display will change if you raise the volume level.

Setting the speaker Level

• Using the on-screen display

1. Press the OSD MENU button.

2. Select “Speaker Setup” and then press the right edge of the

ENTER/Cursor button.

3. Select “Level Setup” and then press the right edge of the

ENTER/Cursor button.

The Level Setup screen appears and a test tone (pink noise) is

output from the left front speaker. You can change the speaker

that outputs the test tone in the following sequence.(When the

cursor is on “Center,” you can press the lower edge of the EN-

TER/Cursor button to display additional items.)

Left (Left front)

Center (Center) Right (Right front) R-Sur

(Right surround)

L-Sur (Left surround) Subwoofer (Subwoofer)

Left.

4. Set the output level of each speaker so that you can hear the

same level of test tone at the listening position.

You can adjust the output level of each speaker in the range of -

12 to +12 dB, except for the subwoofer whose adjustment range

is -30 to +10 dB.

5. Press the center of the ENTER/Cursor button, or press the

EXIT button, to exit the setup mode.

* Level Setup *

Left = +1dB

Center = 0dB

(Right = 0dB)

SP/SYS

SETUP

PRESET/MODE ADJ

PUSH TO ENTER

PRESET/MODE ADJ

PUSH TO ENTER

PRESET/MODE ADJ

PUSH TO ENTER

SPEAKERS

PCM DIGITAL

STEREO

Center

Right

R-Sur

L-Sur

• Using Test button on the remote controller

1. Press the MODE AUDIO button.

2. Press the TEST button.

Left front speaker produces the test tone (pink noise).

3. To adjust the level of each speaker,press the CH SEL, but-

ton to select a speaker and press the LEVEL +/- buttons to

raise or lower the level.

4. Press rhe TEST button to complete adjustment.

23 4

SPEAKERS

DSP

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 63 64

Comments to this Manuals

No comments

Onkyo TX-DS676 User Manual Page 21

Comments to this Manuals

Related products and manuals for Acoustics Onkyo TX-DS676