ONKYO HT-S3505 Instruction Manual download pdf (Page 39)

Advanced Operations

En-39

Audio Selector

■ Audio Selector

` ARC:

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

With this selection, the TV’s audio can be

automatically selected as a priority among other

assignments.

` HDMI:

This can be selected when HDMI IN has been

assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or

OPTICAL IN) have been assigned, HDMI input is

automatically selected as a priority.

` COAXIAL:

This can be selected when COAXIAL IN has been

assigned as an input source. If both coaxial and

HDMI inputs have been assigned, coaxial input is

automatically selected as a priority.

` OPTICAL:

This can be selected when OPTICAL IN has been

assigned as an input source. If both optical and HDMI

inputs have been assigned, optical input is

automatically selected as a priority.

` Analog:

The AV receiver always outputs analog signals.

You can set priorities of audio output when there are both

digital and analog inputs.

Note

• This setting can be made only for the input source that is assigned

as HDMI IN, COAXIAL IN, or OPTICAL IN.

You can select “ARC” if you select the TV/CD input selector.

But you cannot if you’ve selected “Off” in the “Audio Return

Ch” setting (➔ page 42).

Setting the Incoming Digital Signal (Fixed

Mode)

■ Fixed Mode

` Off

The format is detected automatically. If no digital

input signal is present, the corresponding analog

input is used instead.

` PCM:

Only 2-channel PCM format input signals will be

heard. If the input signal is not PCM, the PCM

indicator will flash and noise may also be produced.

` DTS:

Only DTS (but not DTS-HD) format input signals

will be heard. If the input signal is not DTS, the dts

indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is selected

in the “Audio Selector” setting, you can then specify the

signal type in “Fixed Mode”.

Normally, the AV receiver detects the signal format

automatically. However, if you experience either of the

following issues when playing PCM or DTS material, you

can manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut off,

try setting the format to PCM.

• If noise is produced when fast forwarding or reversing a

DTS CD, try setting the format to DTS.

Note

• The setting will be reset to “Off” when you change the setting in

the “Audio Selector” (➔ page 39).

Menu Hardware

OSD

■ Volume OSD

` On

` Off

Turn this setting on to display the volume level on the TV

screen while it is adjusted.

Remote ID

■ Remote ID

` 1

, 2, or 3

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differentiate

the AV receiver from the other components, you can

change its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

Changing the remote controller’s ID

Hardware

While holding down RECEIVER, press and hold

down SETUP until the remote indicator lights

(about 3 seconds).

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

123456

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 71 72

Comments to this Manuals

No comments

ONKYO HT-S3505 Instruction Manual Page 39

Comments to this Manuals

Related products and manuals for Speaker sets ONKYO HT-S3505