Onkyo TX-DS787 User Manual download pdf (Page 48)

Enjoying music in the remote zone

Controlling the TX-DS787 from the remote zone

1. Aiming at the remote sensor, press the ON

button on the remote controller.

Note:

Be aware that if you start using the system in the remote zone

(Zone 2) while a recording is going on in the main zone, the

recording will be stopped in the main zone.

2. Press the appropriate input selector button on

the remote controller to select the desired

source.

3. Adjust the volume to the desired level.

Notes:

• If the source for the main zone is selected as the source for the

remote zone and the source for the main zone is changed, then

the source for the remote zone will change as well.

• In the remote zone, you can only play the source in the 2-

channel mode. You cannot play the source in the remote zone

in the surround mode.

• You can only play the source in the Stereo mode or Direct

mode in the main zone, when you are playing the source in the

remote zone.

• If the Rec Out button is pressed in the main room while

someone is using the system in the remote zone, the Zone 2

function will be deactivated and the source will turn off in the

remote zone.

• The Zone 2 terminal is an analog output. Digital signals are not

output. If no sound is heard from the selected input source,

check if the component is connected to the analog inputs.

• Please note that some third-party multi-room system

components may not be fully compatible with the Onkyo

multi-room system components.

To select the same source for the remote zone that is selected

for the main zone, press the Zone 2 button again until

“Zone2Sel:SOURCE” appears in the display.

Adjusting the volume for the remote zone at the

TX-DS787

Following the procedure given below, you can adjust the volume

for the remote zone at the TX-DS787 without using the remote

controller.

1. Press the ZONE 2 VOL button.

2. While “ZONE 2Volume” is displayed, turn the

SSC dial to adjust the volume to the desired

level.

Controlling the TX-DS787 without the remote

controller

1. Press the Zone 2 button on the TX-DS787.

Ex.: When the CD button is pressed.

When “Zone2Sel:Off” is displayed, the output to the remote

zone is turned off.

TUNING

UPDOWN

MUTE

MODE

DISPLAY STEREO

CHARACTER

MEMORY

DIRECT THX

SURROUND

BASS

TREBLE

EXIT

LISTENING

MODE

ZONE 2 VOL

CH LEVEL

AM PHONO C

TAPEDVD

VIDEO

VCR

VIDEO

VCR

STANDBY/

POWER

ANDBY

ZONE

OFF

REC OUT ZONE

PHONES

RECEIVER

TX-DS

787

MASTER VOLUME

VIDEO AUDIOLR

VIDEO CAM INPUT/4

VIDEO

S VIDEO

AUDIO SELECTOR

PUSH TO ENTER

SMART SCAN

CONTROLLER

DSP/

PRESET

OPEN/CLOSEREC

AUDIO MUTING

DISCTRACK

DVD

TUN

T2T1

STEREO

123

654

10 0

ENT

SURROUND THX DSP

LEVEL

CH SELRe-EQ

LEVEL

–

DIMMER

HOME THEATER CONTROLLER

RC-390M

LATE NIGHT

DIRECT DSP

V2 V3 V

–

VOL

ZONE 2

ZONE 2 VOL

SSC

DTS

PTY/

Input source buttons

ZONE 2 indicator

INPUT

SELECTOR

buttons

Caution:

If you are not using the system in the remote Zone, always

press the ZONE 2 button consecutively to turn the ZONE 2

function off.

2. Select a source.

After pressing the Zone 2 button, you must press an input

source button within 3 seconds. The Zone 2 indicator lights.

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 75 76

Comments to this Manuals

No comments

Onkyo TX-DS787 User Manual Page 48

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Onkyo TX-DS787