Onkyo AV RECEIVER TX-NR1009 User Manual Page 61
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
61
En
Note
• Only the input source assigned to the HDMI IN via “HDMI
Input” is enabled (➔ page 45).
• The power consumption during standby mode will increase
during the HDMI Through function; however in the following
cases, the power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
• Depending on the connected component, the correct input source
may not be selected with the setting set to “Auto”.
• This setting is set to “Off” automatically when the “HDMI
Control(RIHD)” setting is set to “Off”.
■ Audio TV Out
` Off
` On
This preference determines whether the incoming audio
signal is output from the HDMI output. You may want to
turn this preference on if your TV is connected to the
HDMI output and you want to listen to the audio from a
connected component through your TV’s speakers.
Normally, this should be set to “Off”.
Note
•If “On” is selected and the audio can be output from the TV, the
AV receiver will output no sound through its speakers. In this
case, “TV Speaker” appears on the display by pressing
DISPLAY.
•When
“HDMI Control(RIHD)” is set to “On”, this setting is
fixed to
“Auto”.
• With some TVs and input signals, no sound may be output even
when this setting is set to
“On”.
•When “Audio TV Out” or
“HDMI Control(RIHD)” is set to
“On” and you’re listening through your TV’s speakers
(➔ page 17), turning up the AV receiver’s volume control will
make the sound be output from the AV receiver’s front left and
right speakers. To stop the AV receiver’s speakers producing
sound, change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
• Listening mode cannot be changed when this setting is set to
“On” and the input source is not HDMI.
•If the “Monitor Out” setting is set to “Both(Main)” or
“Both(Sub)” (➔ page 45) and if your TV connected to a
priority output cannot output the audio, the sound will be heard
from AV receiver’s speakers.
■ Audio Return Channel
` Off
` Auto
:
The audio signal from your TV tuner can be sent to
the HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to the HDMI OUT
MAIN of the AV receiver. To use this function, you must
select the TV/CD input selector and your TV must be
ARC capable.
Note
• If you set “Audio Return Channel” to “Auto”, the “Audio
Selector” settings of the TV/CD input selector will be
automatically switched to “ARC” (➔ page 57).
•The “Audio Return Channel” setting can be set only when the
“HDMI Control(RIHD)” setting is set to “On”.
• This setting is set to “Auto” automatically when the “HDMI
Control(RIHD)” is set to “On” for the first time.
■ Lip Sync
` Off
` On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
• If the “Monitor Out” setting is set to “HDMI Main”,
“Both(Main)” or “Both” (➔ page 45), the delay will be
corrected in accordance with the monitor connected to HDMI
OUT MAIN. On the other hand, if “HDMI Sub” or
“Both(Sub)” is selected, the delay will be corrected in
accordance with the monitor connected to HDMI OUT SUB.
Auto Standby
■ Auto Standby
` Off
` On
When “Auto Standby” is set to “On”, the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video
signal input.
“Auto Standby” will appear on the display and OSD 30
seconds before the Auto Standby comes on.
Default setting: On (European and Asian models), Off
(North American models)
Note
•Set to “
On”, the Auto Standby function may activate itself
during playback with some sources.
•The Auto
Standby function does not work when Zone 2/3 is on.
After changing the settings of the “HDMI
Control(RIHD)
”, “HDMI Through” or “Audio
Return Channel”
turn off the power on all connected
pieces of equipment and then turn them on again. Refer
to the user’s manuals for all connected pieces of
equipment.
- TX-NR1009 1
- Important Safety Instructions 2
- For U.S. models 3
- For Canadian Models 3
- Modèle pour les Canadien 3
- Supplied Accessories 4
- Contents 5
- Features 6
- Front Panel 8
- Rear Panel 10
- Remote Controller 11
- Connecting the AV Receiver 12
- Speaker Configuration 13
- Using Dipole Speakers 14
- Using a Powered Subwoofer 14
- Bi-amping the Front Speakers 14
- Connecting a Power Amplifier 15
- About AV Connections 16
- FDH KE G JI 18
- Connecting Onkyo u Components 20
- Connecting the Antennas 21
- Connecting the Power Cord 21
- Turning On 22
- Turning Off 22
- Playback 23
- Playing a USB Device 25
- Listening to Internet Radio 25
- Registering My Favorites 26
- Remote Playback 27
- Listening to AM/FM Radio 28
- Presetting AM/FM Stations 29
- Using Basic Functions 31
- AUDYSSEY 32
- Ambient noise is too high 33
- MultEQ XT: Auto Setup 33
- Using the Listening Modes 34
- About Listening Modes 35
- ■ Listening Modes 36
- THX S2 C i nema 39
- THX S2 Music 39
- T H X S 2 G a m e s 39
- THX Su r r EX 39
- Using the Home Menu 40
- Using the Sleep Timer 40
- Displaying Source Information 41
- Changing the Input Display 41
- Using the Whole House Mode 41
- Selecting Speaker Layout 42
- Muting the AV Receiver 42
- Using Headphones 42
- Using Easy Macros 43
- Recording 43
- Advanced Setup 44
- Input/Output Assign 45
- HDMI Input 46
- Component Video Input 46
- Speaker Setup 47
- Speaker Distance 49
- Level Calibration 49
- Equalizer Settings 50
- THX Audio Setup 50
- Audio Adjust 51
- Audyssey DSX™ 52
- Theater-Dimensional 52
- LFE Level 52
- Source Setup 53
- IntelliVolume 54
- A/V Sync 54
- Name Edit 54
- Shift All Erase 55
- 4 - 4. Name Edit 55
- Audio Selector 57
- Listening Mode Preset 58
- Miscellaneous 59
- Hardware Setup 59
- “On”, change the setting 60
- Auto Standby 61
- Firmware Update 62
- Using the Audio Settings 63
- Speaker Levels 64
- Dolby Volume 64
- Audyssey 64
- Late Night 64
- Music Optimizer 65
- Screen Centered Dialog 65
- Multi Zone 66
- 12V Trigger Out 67
- Muting Zones 68
- Components 69
- Using the Onkyo Dock 70
- Controlling Your iPod/iPhone 71
- ✔: Available buttons 72
- Controlling Other Components 73
- Entering Remote Control Codes 74
- Components Connected via u 75
- Resetting REMOTE MODE Buttons 75
- Learning Commands 77
- Using Normal Macros 78
- RECEIVER 79
- UP-A1 Dock for iPod/iPhone 82
- Zone 2/3 82
- USB Device Playback 83
- Troubleshooting 86
- Before you start 86
- Update procedure 86
- Updating the Firmware via USB 86
- MONITOR OUT 88
- HDMICoaxial Analog 89
- HDMI Analog 89
- Multichannel 89
- Video Resolution Chart 90
- About p-compatible components 91
- About HDMI 93
- Network/USB Features 94
- Server Requirements 95
- USB Device Requirements 95
- Supported Audio File Formats 96
- About DLNA 96
- Specifications 97
- ■ Audio Outputs 98
- ■ Others 98
Related products and manuals for Receivers and Amplifiers Onkyo AV RECEIVER TX-NR1009
(63 pages)© 2020, manymanuals.com. All rights reserved. | 0.123 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals